EM - Y2V2_Practical_V1.3
Course Instructor
MAHA SKILLS
FREE
To enroll in this course, please contact the Admin
/CourseBundles(90)/1408-EM_TP_Y2V2.jpg)
Course Overview
Schedule of Classes
Course Curriculum
1 Subject
EM - Y2V2_Practical_V1.3
59 Learning Materials
Module 8: Fiber Optic Communication
Ex 200 - Identify the resources and their need on the given fiber optic trainer kit.
Ex 201 - Make optical fiber setup to transmit and receive analog and digital data.
Ex 202 - Set up the OFC trainer kit to study AM, FM, PWM modulation and demodulation.
Ex 203 - Perform FM modulation and demodulation using OFC trainer kit using audio signal
Ex 204 - Perform PWM modulation and demodulation using OFC trainer kit using audio signal
Ex 205 - Perform PPM modulation and demodulation using OFC trainer kit using audio signal
Module 9: Digital Panel Meter
Ex 206 - Identify LED Display module and its decoder/driver ICs
Ex 207 - Display a word on a two line LED
Ex 208 - Measure/current flowing through a resistor and display it on LED Module
Ex 209 - Measure/current flowing through a sensor and display it on a LED module (DPM)
Ex 210 - Identify LCD Display module and its decoder/driver ICs
Ex 211 - Measure/current flowing through a resistor and display it
Module 10: SMPS And Inverter
Ex 212 - Identify the components/devices and draw their corresponding symbols.
Ex 213 - Dismantle the given stabilizer and find major sections/ ICs components.
Ex 214 - List the defect and symptom in the faulty SMPS.
Ex 215 - Measure / Monitor major test points of computer SMPS.
Ex 216 - Troubleshoot the fault in the given SMPS unit. Rectify the defect and verify the output
Ex 217 - Use SMPS used in TVs and PCs for Practice.
Ex 218 - Install and test the SMPS in PC.
Ex 219 - Install and test an inverter
Ex 220 - Troubleshoot the fault in the given inverter unit. Rectify the defects and verify
Ex 221 - Construct and test IC Based DC-DC converter for different voltages.
Ex 222 - Construct and test a switching step down regulator using LM2576
Ex 223 - Construct and test a switching step up regulator using MC 34063
Module 11: UPS
Ex 224 - Connect battery stack to the UPS.
Ex 225 - Identify front panel control & indicators of UPS
Ex 226 - Connect Battery & load to UPS & test on battery mode
Ex 227 - Open top cover of a UPS; identify its isolator transformers, the UPS transformer
Ex 228 - Identify the various test point and verify the voltages on these.
Ex 229 - Identify various circuit boards in UPS and monitor voltages at various test points.
Ex 230 - Perform load test to measure backup time.
Module 12: Solar Power (Renewable Energy System)
Ex 231A - Wire a solar controller to a battery storage station.
Ex 231B - Install a solar panel to a roof
Ex 232 - Connect storage batteries to a power inverter
Ex 233 - Connect and test solar panel to the Inverter and run the load.
Ex 234 - Install a solar power to charge a rechargeable 12 V DC battery and find out the charge
Ex 235 - Install a Solar Inverter
Module 13: Cell Phones
Ex 236 - Dismantle, identify the parts and assemble different types of smart phones.
Ex 237 - Dismantle the cell phone/smart phone remove the key pad and clean it,
Ex 238 - Interface the cell phone/smart phone to the PC and transfer the data card.
Ex 239 - Flash the various brands of cell phone/smart phone (at least 3).
Ex 240 - Format the cell phone/ smart phone for virus (approach the mobile repair shop)
Ex 241 - Perform the interfacing of cell phone/smart phone to the PC and dismantle the cell phone
Ex 242A - Unlock the handsets through codes and software
Ex 242B - Find out the fault of basic cell phone system. Rectify the fault in ringer section
Ex 243 - Replace various faulty parts like mic, speaker
Module 14: LED Lights
Ex 244 - Dismantle the LED light, identify the connections of LEDs stacks, protection circuits
Ex 245 - Identify the rectifier, controller part of LED lights.
Ex 246 - Make series string connection of six LED’s and connect four Series strings in parallel.
Ex 247 - Connect to such parallel sets in Series to create a matrix of LED’s.
Ex 248 - Apply suitable voltage and check Voltage across series strings.
Module 15: LCD And LED TV
Ex 249 - Identify and operate different Controls on LCD, LED TV.
Ex 250 - Identify components and different sectors of LCD and LED TV.
Ex 251 - Dismantle; Identify the parts of the remote control.
Ex 252 - Dismantle the given LCD/LED TV to find faults with input stages through connectors.
Ex 253 - Detect the defect in a LED/LCD TV receiver given to you. Rectify the fault.
Ex 254 - Troubleshoot the faults in the given LED/LCD TV receiver. Locate and rectify the faults.
Ex 255 - Test LED/LCD TV after troubleshooting the defects.
Ex 256 - Identify various connectors and connect the cable operators external decoder to the TV.
Course Instructor
MAHA SKILLS
538 Courses • 127459 Students
By clicking on Continue, I accept the Terms & Conditions,
Privacy Policy & Refund Policy